Re: Clutch Slave Cylinder
The only 1" cylinder I found was in the classic Girling style off an old Land Rover. The only downside was it took some effort to operate and tiring in traffic!! I've reverted back to standard.
Re: Clutch Slave Cylinder
Is the clutch too light or are you not getting enough travel?
If it's a travel issue, little you can do bar fit a different pedal assembly.
Re: Clutch Slave Cylinder
Quote:
Originally Posted by
strat24v
Is the clutch too light or are you not getting enough travel?
If it's a travel issue, little you can do bar fit a different pedal assembly.
Can you alter the ratio on the standard pedal by moving the point where the master cylinder connects?
Phil would a 7/8" cylinder not suffice?
1 Attachment(s)
Re: Clutch Slave Cylinder
Craig / John
Yes the travel is insufficient with a 19.05 dia piston
Also the master cylinder is right up underneath the dash..... a slight GIT to get at
The point where the cylinder connects is all welded up..... so I am trying to boge it up along the least line of resistance !!!
7/8" may suffice..... but I think a 1" would suffice even more !.....even if I end up with one leg like Schwarzenegger !
Got this one from Rally Designs on the way....... I will have the Grinder and hammer ready for when it arrives !!
Attachment 11098
Thanks for your inputs
Re: Clutch Slave Cylinder
Next time we meet Craig...... Please call me a twat......I fitted the 1" master cylinder and even Schwarzenegger would struggle to push it !!.... I will go shopping for a 7/8" .......
i need a lesson in clutch ratios and lever distances...
Re: Clutch Slave Cylinder
Phil
I will be happy to swap a lesson of calculating using the formulas described on the note with a pizza next week !! the day will be yours ....... The restaurant is already well known ;)
But first please you have to read and reread 100 times this note ......
Concentrate your reading on pages 6/7/8
https://www.epsic.ch/phocadownload/B...0mecanique.pdf
If any probleme with language just drop me a call :rolleyes:
Re: Clutch Slave Cylinder
13/16" also available.....
Re: Clutch Slave Cylinder
Quote:
Originally Posted by
Bernard
Next time we meet Craig...... Please call me a twat......I fitted the 1" master cylinder and even Schwarzenegger would struggle to push it !!.... I will go shopping for a 7/8" .......
i need a lesson in clutch ratios and lever distances...
Reading back the earlier posts, the problem was lack of travel, so 7/8" would be the way to go, 1" is a bigger piston, so will reduce the travel...... think you may have your calculator upside down ;)
Re: Clutch Slave Cylinder
Quote:
Originally Posted by
Bernard
Next time we meet Craig...... Please call me a twat......I fitted the 1" master cylinder and even Schwarzenegger would struggle to push it !!.... I will go shopping for a 7/8" .......
i need a lesson in clutch ratios and lever distances...
You need a lesson in pedal box fitting! Get hacking at that front bulkhead and fit a tilton or wilwood assembly and don't cut the pedals shorter or you are back to square one.
Re: Clutch Slave Cylinder
That did cross my mind... just want to get her mobile as quick as I can.... may be a summer job ?
Quote:
Originally Posted by
strat24v
You need a lesson in pedal box fitting! Get hacking at that front bulkhead and fit a tilton or wilwood assembly and don't cut the pedals shorter or you are back to square one.
Re: Clutch Slave Cylinder
Not sure what the problem is? Is Nellie a Hawk and powerplant a 164 v6 12v? This is my config running original clutch master cylinder (X1/9) into 164 12v slave seems to work.
Re: Clutch Slave Cylinder
Quote:
Originally Posted by
Lancialulu
Not sure what the problem is? Is Nellie a Hawk and powerplant a 164 v6 12v?
12v to 24v conversion Tim:
http://www.stratosec.com/Forum/showt...splant-begins?
Phil,
Can you re-engineer the ratio on the clutch/slave/lever end, and leave the tricky inaccesible pedal/master cylinder well alone?
Assuming the pedal end is healthy and functioning ok, that is?
Re: Clutch Slave Cylinder
Quote:
Originally Posted by
ProtoTipo
12v to 24v conversion Tim:
http://www.stratosec.com/Forum/showt...splant-begins?
Phil,
Can you re-engineer the ratio on the clutch/slave/lever end, and leave the tricky inaccesible pedal/master cylinder well alone?
Assuming the pedal end is healthy and functioning ok, that is?
Mmmmmmmmm... its a bit late for that Chris....I've had mi grinder out !!..... Oooohhhhheeerrrr
Re: Clutch Slave Cylinder
Update... I have a clutch !....the problem appears to be the push rod between the slave cylinder and the clutch lever arm being too short !.... I have a 166 six speed gearbox with a DMF, a Tilton 7/8" MC, I am using the LB selector system, in doing this you need to use a 156 slave cylinder mounting bracket....everything looks good so far. But what I didn't notice was when installing the slave cylinder the push rod did not go very far into the slave cylinder thus it didn't have full travel...... So I made a longer push rod (about 15mm longer) fitted it all up and I now have enough travel to disengage the clutch.
hope someone finds this useful in the future...... Almost threw the towel in...
So took Nellie for a run and found that the engine loses throttle at 2000rpm...... Did manage to select all six gears tho
getting there... Slowly
Phil