View Full Version : Alfa Clearout
Selling all my Alfa 164 3ltr engine bits to fund new engine
Complete 3ltr 12v including new clutch (0 miles), ECU with wiring loom standard manifolds everything needed to run the engine. Has done less than 6000 miles since rebuild but has been stood for a few of years (does turn over) £350 ono Includes 5 speed box which will need looking, hard to get into first and second
2 x 24v ECU (0 261 200 663) £80 each
1 x Wiring loom for a above ECU £20
24v manifolds £80
12v 3 into 1 manfolds £100
Have got a complete 24v which I am breaking for parts
24v head gasket set ( includes cam oil seals, exhaust gaskets etc) £150
Hawk gear linkage offers
Can bring small parts to Stoneleigh
ChrisCar6
26-04-2017, 23:44
I'll buy the 24v Ecu loom if it is in good nick....
tomsredstratos
26-04-2017, 23:55
Hi Alan,
Could you post a photo of the 12v engine,or email it to me if you have one handy.
Thanks.
Tom.
I'm interested in the head gasket set if it's good for a 2.5l 24v. I'll be at Stoneleigh on the Sunday...
Mark
I'll buy the 24v Ecu loom if it is in good nick....Sorry Chris loom has sold
1118011181
Hi Alan,
Could you post a photo of the 12v engine,or email it to me if you have one handy.
Thanks.
Tom.
I'm interested in the head gasket set if it's good for a 2.5l 24v. I'll be at Stoneleigh on the Sunday...
Mark The gasket set is just for the 3ltr
tomsredstratos
28-04-2017, 11:03
Alan,
You have a pm.
Tom
turbonutter
28-04-2017, 11:06
Selling all my Alfa 164 3ltr engine bits to fund new engine
I have to ask? Why are you swapping out the Alfa v6 and for what?
I have to ask? Why are you swapping out the Alfa v6 and for what?
Thought i would go for something newer and more available, Ford 3ltr V6 out of ST220
Thought i would go for something newer and more available, Ford 3ltr V6 out of ST220
Hi Skelly....that will be different...I will look forward to the build photos....good luck with it...Phil
turbonutter
28-04-2017, 20:17
Yes definitely a one off installation, so I guess its not an easy install - Hope it is all going well, It will be interesting to see when its done :)
ProtoTipo
29-04-2017, 07:58
Mmmmmmmm !!
http://www.stdrivers.co.uk/forum/uploads/1216977559-engine.jpg
And why not you have to ask?
At the first couple of shows we did with the ListerBell the ST220 engine was talked about quite a bit by prospective customers.
That was before Craig started thinking about Toyota engines of course.
But the Duratec has proven mid engined installation with Noble so following their cooling model would probably be a good idea.
Good aftermarket of tuning parts for the Duratec 2.0, how is it for the V6? Something that isn't around for the Alfa that's for sure!
Ken Tomblin
29-04-2017, 21:07
mountune are good for tuning the Duratec and Jaguar AJ 30 v6 engines, good info on the Locost AJ 30 Web site, good power, rev to 8000 rpm and cheap parts!!!!!
ProtoTipo
29-04-2017, 21:20
mountune are good for the Duratec and Jaguar AJ 30 v6 engines, good info on the Locost AJ 30 Web site, good power, rev to 8000 rpm and cheap parts!!!!!
Aftermarket period looking cam covers are available for 4 pot Duratecs.
Some Jaguar badged ones would be good for this V6?
Hawk Gear linkage for Alfa 164 3Ltr V6, 5 speed box
11209
Most parts sold
Only have 1 x 24v ECU left and now thanks to the Slug posting that 24v ECU for sale will have to reduce the price on mine :( Cheers Ian;)
Still got the rear anti roll bar
Skelly
The Slug
23-05-2017, 09:51
Your is tested and working Skelly, can you say the same for the other one?
Buyer beware...
Guy Mayers
23-05-2017, 10:19
Did the gear linkage sell Alan?
Guy
Did the gear linkage sell Alan?
Guy
Sorry Guy for not letting you know, Yes the linkage has been sold.
Your is tested and working Skelly, can you say the same for the other one?
Buyer beware...
Good point, should ask for more:D
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.