...which now fits nicely with inlet pipe and air filter mounted above the left-hand rear wheel...
Michael
...which now fits nicely with inlet pipe and air filter mounted above the left-hand rear wheel...
Michael
Hi guys, some more updates...
Doors are now hung. Took the best part of a weekend getting them to line up - very fiddly. We initially used the the original Litton door brackets, but since the pics below were taken, they've been swapped for items from Napier Sport purchased a couple of years ago, which are much stronger. The hinges are Litton items and we used Renault Clio straps, which work very well.
Here's a pic sitting in the drivers seat for the first time.
My Dad has completed some of the upholstery on the underside of the roof and A-posts. Not bad considering he's never used a sewing machine before...
Some exterior pics of the car - door alignment has been improved since these pics.
Last edited by MichaelEustace; 09-11-2014 at 21:40.
First side window fitted
Windows seals are next to be fitted.
Wow Michael,
you did a great work step on the car,
fantastic solution with the door hinges and straps,
btw: you did mount the catches on the front bonnet strange, why?
Enzo
Do the Clio door straps operate to the full range of movement as per the original Clio application? I.E. Is the 2 stage "checking" mechanism deployed when the door's opened? .Originally Posted by MichaelEustace
Hi guys, some more updates...
Doors are now hung. Took the best part of a weekend getting them to line up - very fiddly. We initially used the the original Litton door brackets, but since the pics below were taken, they've been swapped for items from Napier Sport purchased a couple of years ago, which are much stronger. The hinges are Litton items and we used Renault Clio straps, which work very well.
Sorry for such a delayed reply. The door check straps are actually 'Peugeot 206 Door Hinge Stop Check Strap Front 3DR 5DR N/S O/S 9181C8'. These may well be shared with other cars but these are the ones I ordered! On the drivers door I shortened the check strap by cutting and welding an overlap that resulted in the fully open position providing a few millimetres clearance from the front clam shell.
The passenger door doesn't open quite so far. The passenger door only has one stage of opening but the drivers door has two stages.
Last edited by Paul Eustace; 14-10-2015 at 19:55.
Michael and I now have the car through the IVA test and the certificate and registration documentation is with the DVLA team.
We learnt a few things along the way:
To improve the speedometer accuracy I mounted my VDO speedometer inductive sensor on the gearbox lined up with a Fiat Ducato reluctor ring that I mounted on the differential flange. 54 teeth per revolution results in a really smooth and accurate speedometer. I also ran a screened cable for the speedometer wiring as the speedo was susceptible to interference resulting in the needle flickering whilst at a standstill.
The VDO tachometer was erratic when driven from my Bosch distributor with inductive pickup and electronic amplification! A simple diode in the tachometer feed results in a smooth rev counter needle.
I at last brought the correct size springs (Coilover Spring Faulkner 10.5 Inches Long - 2.25 Inch Inside Diameter | FRS-105-200) for my front Leda shocks and now I can mount the shocks the right way up.
I fitted new front suspension ball joints, top and bottom, plus repacked the Litton steering rack with EP grease. The front steering is now really nice and self centring is as it should be.
I have re-aligned the front suspension to 10 minutes toe in, 40 minutes negative camber, 4 degrees of castor. The rear suspension has 10 minutes of toe in and 1 degree of negative camber.
I have 205/50VR15's on the front and 225/50VR15's on the rear. I am currently running 16psi in the front and 20psi in the rear but I suspect these are too high. 350kgs front axle and 540kgs rear with full fuel tanks, 90litres.
I fitted rear mudguards to meet the wheel covering requirements.
Guy Croft solved my over fuelling problems by recommending that I fit a fuel pressure regulator. My engine ran fine with just a couple of gallons in the fuel tanks but when I brimmed the tanks for the IVA test I could not meet the emissions test. The Silver Top road specification fuel pump is able to overcome the Weber DCOE 45 needle valves and neat fuel drips from the accelerator pump jets! A Malpassi Filter King from Northampton Motor Sport cured this issue and we sailed through the emissions test.
Photograph shows the reluctor ring on the differential flange and the speedometer inductive pickup mounted in my bracket.
Whilst I am waiting for the DVLA to process my paperwork and provide me with a registration number I have a few other things to do:
I am currently working on a steady bar for the engine. I have not used the Lancia head mounted solution as this leads to head gasket issues. I have designed a bell housing mounted solution. I will post some photographs soon.
Last edited by Paul Eustace; 16-10-2015 at 18:04. Reason: correction
Hi Paul. Well done on the IVA.
Good tip on the reluctor ring. I guess the more pulses there are the more accurate and steady the signal?
Do you have the welded top front shock bracket or bolt on triangular brackets?
What open and closed lengths are the front shocks?
I did use Clio check links. Bit fiddly to fit but do the job well. Can post pic if you like?
Posting Permissions
Reply With Quote
Bookmarks