Getting off my arse

[bosmass]

What I ended up doing before I put the body on was getting the wheels set up in acceptable positions, at least to my eye. Basically as close as possible toe, camber etc. still all by eye. I also matched adjustments side to side so that if i ended up making changes on one side I was pretty sure of what the other was going to be. On my kit which is all Lister Bell, there were only changes made to the interior wheel well panels to clear the rear tires (15" wide oem style) on full shock.

With all of that being said, now my engine is in the suspension has settled more and things need a final adjustment. I think there is a newer dimension sheet that shows the optimal set up. I saw it posted a few months ago.

[tipo158]

What I ended up doing before I put the body on was getting the wheels set up in acceptable positions, at least to my eye. Basically as close as possible toe, camber etc. still all by eye. I also matched adjustments side to side so that if i ended up making changes on one side I was pretty sure of what the other was going to be. On my kit which is all Lister Bell, there were only changes made to the interior wheel well panels to clear the rear tires (15" wide oem style) on full shock.

With all of that being said, now my engine is in the suspension has settled more and things need a final adjustment. I think there is a newer dimension sheet that shows the optimal set up. I saw it posted a few months ago.

Yes, I did the visual close setup also, just haven't done the final, by the numbers, setup. Paul and I have a similar setup, Corse chassis's with Lister-Bell bodies.

Corky

[tipo158]

I have decided to go with an in tank fuel pump, but as you can see from the photo, the leads for the pump are a little short. I had a hard time finding the correct in fuel tank wire, but finally located some. They listed their wire to be purchased by the foot with a ten foot minimum, so since I only needed about 3 feet, I ordered the minimum, the other photo is what they sent me. I'd be willing to bet that there is more then ten feet on each spool. Now I am waiting for the gland to put through the plate so that I can pass the wires through it.

[tipo158]

Well, I thought I had all the parts to finish the tank. Needed new connectors for the longer wires for the fuel pump and couldn't find them locally so I had to order them on the internet. The round over valve needed a bulkhead fitting like I told the man at the speed shop (who assured me I didn't). So I located the gland for the wires to path through the tank top as well as the location for the rollover valve. In the photo, the black and blue piece is the out flow of the tank, the blue and red piece in the return line, the blue, red and gold piece is the rollover valve, the black piece is the gland for the wiring. So, sometime next week, the rest of the parts should get here and I can put the tank back together.

Corky

[tipo158]

Finally got the connectors that I needed, the intank fuel pump is now wired and installed.

Corky

[tipo158]

Modified the plug wire ends so that I can use the coil pack I have. Need to figure out a mounting bracket for the coil pack. Thinking about mounting it so it is in the approximate spot where a distributor would be. I spent way too much time trying to find either a wire set that I could use or a coil pack that would work with the plug wires that I had. Now I'm trying to decides which way I want to set up the injection system, paired or sequential. Still a ways from getting the engine running.

[tipo158]

Well, I've been having several frustrating days. If I had this to do over again, I would not have purchased the kit that I did. I also wish that there had been full disclosure of exactly what the kit was made up of. The kit was not built as a kit, it was an old chassis, some suspension parts and a bunch other assorted parts that looked like they would be needed for completion of the kit. I am finding that parts are not what they should be, so I'm either having to alter them or fab new parts if I can not source them. There is a LB kit coming to my area, so I will be able to see what a proper kit car looks like when it was build as a unit. I'm sure that I will eventually finish my car, but the frustration of every time I go to do something and things don't fit, or the parts are the wrong ones, or the parts are incomplete or broken, is taking a toll.