Results 1 to 7 of 7

Thread: 7/8" Master Cylinder

  1. #1
    SEC Member
    Join Date
    Sep 2011
    Location
    Cheshire
    Posts
    2,535
    Rep Power
    38

    7/8" Master Cylinder

    Anyone have a 7/8" bore (0.875) Girling pattern Master Cylinder lying about?
    Preferably with the integral reservoir, but not essential?
    Last edited by john; 18-06-2015 at 12:55.

  2. #2
    SEC Member Bernard's Avatar
    Join Date
    Sep 2011
    Location
    Southwell, Nottinghamshire
    Posts
    1,857
    Rep Power
    31

    Re: 7/8" Master Cylinder

    http://www.rimmerbros.co.uk/Item--i-...FW7KtAodo7ELrw

    Can't remember the bore size John although I have a suspicion it was 7/8"

    phil

  3. #3
    SEC Member Bernard's Avatar
    Join Date
    Sep 2011
    Location
    Southwell, Nottinghamshire
    Posts
    1,857
    Rep Power
    31

    Re: 7/8" Master Cylinder


  4. #4
    SEC Member
    Join Date
    Sep 2011
    Location
    Cheshire
    Posts
    2,535
    Rep Power
    38

    Re: 7/8" Master Cylinder

    Thanks Phil.
    But I should have said it's for a bias pedal box so I'm just after a single cylinder, not tandem.
    Good news is that Compbrake are back in business and not too far up the road so I'm collecting one from them in the morning.
    http://www.compbrake.com/product/mas...-0-875-remote/

    Remote reservoir type but they do a reservoir which does screw straight into the master cylinder (if I can squeeze it down far enough for the front clam to close).

  5. #5
    Free user Sando's Avatar
    Join Date
    Sep 2011
    Location
    Middle England North Notts
    Posts
    796
    Rep Power
    0

    Re: 7/8" Master Cylinder

    Hi john
    let me check tomorrow.
    I've got several sizes that I tried when I looked at a bias pedal set up. All brand new just used for a few miles to test.
    Rob

  6. #6
    Free user Sando's Avatar
    Join Date
    Sep 2011
    Location
    Middle England North Notts
    Posts
    796
    Rep Power
    0

    Re: 7/8" Master Cylinder

    Hi John
    Sorry closest I have is 3/4
    Rob
    Attached Thumbnails Attached Thumbnails WP_20150619_001.jpg  

  7. #7
    SEC Member
    Join Date
    Sep 2011
    Location
    Cheshire
    Posts
    2,535
    Rep Power
    38

    Re: 7/8" Master Cylinder

    No worries Rob. Thanks for looking.
    Have bitten the bullet and got a new 7/8" master cylinder.
    Off on hols for a week so didn't want to leave the car immobile in the workshop.....

Similar Threads

  1. Billy Coleman - "The Millstreet Maestro"
    By manta356 in forum Stratos Forum
    Replies: 2
    Last Post: 04-12-2020, 10:30
  2. Clutch master cylinder
    By red5 in forum Alfa V6 Engine and Gearbox
    Replies: 7
    Last Post: 23-06-2016, 15:57
  3. "Alfa-to-Ferrari" Engine Conversion
    By stratosfear in forum Stratos Forum
    Replies: 12
    Last Post: 23-09-2012, 15:52
  4. Master Cylinder
    By Martin Crikey in forum Brakes
    Replies: 19
    Last Post: 17-04-2012, 00:26
  5. Master cylinder fittings
    By catswhiskers in forum Brakes
    Replies: 6
    Last Post: 14-10-2011, 12:06

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •