Results 1 to 6 of 6

Thread: Front axle kit!

  1. #1
    SEC Member Allora#2's Avatar
    Join Date
    Sep 2011
    Location
    GERMANY
    Posts
    635
    Rep Power
    18

    Front axle kit!

    For sale front axle kit for Stratos replica.
    Steering knuckle, wheel bearing set, ball joint above and below, wheel hub, steering arm, wheel bearing cover, everything for right and left.
    550.- Euro shipping possible.
    Inquiries to lancia-stratos@web.de
    or here with PM

    Zu verkaufen Vorderachskit für Stratos Nachbau.
    Achsschenkel, Radlagersatz, Kugelgelenk oben und unten, Radnabe, Lenkhebel, Radlagerdeckel, alles für rechts und links.
    550,- Euro Versand möglich.
    Anfragen an lancia-stratos@web.de
    Attached Thumbnails Attached Thumbnails IMG_0394.jpg  

  2. #2
    SEC Member Allora#2's Avatar
    Join Date
    Sep 2011
    Location
    GERMANY
    Posts
    635
    Rep Power
    18

    Re: Front axle kit!

    SOLD

    thank you for the interest.
    Last edited by Allora#2; 10-03-2022 at 20:07.

  3. #3
    SEC Member
    Join Date
    Aug 2016
    Location
    Leicestershire
    Posts
    81
    Rep Power
    7

    Re: Front axle kit!

    Good morning.
    Congratulations on the sale. quick question if you don't mind. It looks a similar set up to my suspension on my Corse, of which I know nothing of its origin.
    What are the bottom ball joints from I have the three bolt type converting to the ones in your picture would give more adjustment for the geometry.
    Thanks Sach.

  4. #4
    SEC Member Strat Fan's Avatar
    Join Date
    Sep 2011
    Location
    East Notts
    Posts
    995
    Rep Power
    21

    Re: Front axle kit!

    Quote Originally Posted by sdebez View Post
    Good morning.
    Congratulations on the sale. quick question if you don't mind. It looks a similar set up to my suspension on my Corse, of which I know nothing of its origin.
    What are the bottom ball joints from I have the three bolt type converting to the ones in your picture would give more adjustment for the geometry.
    Thanks Sach.
    The ball joint shown in the lower part of the front upright is actually the top ball joint. It does not belong in the position shown.
    The genuine Stratos uses a 3 bolt ball joint in the lower position.
    You wouldn't really want a threaded joint of that type in that position because of the way the damper loads would be fed through it into the upright.
    The Corse camber is a bit of a pain because it is done on the inner end of the TCA.
    Last edited by Strat Fan; 13-03-2022 at 12:32.
    "You can lead a horse to water, but a pencil must be lead"
    Stan Laurel

  5. #5
    Site Supporter ProtoTipo's Avatar
    Join Date
    Sep 2011
    Location
    Outer Mongolia
    Posts
    4,231
    Rep Power
    54

    Re: Front axle kit!


  6. #6
    SEC Member
    Join Date
    Aug 2016
    Location
    Leicestershire
    Posts
    81
    Rep Power
    7

    Re: Front axle kit!

    That what i was thinking, trying to make the camber adjust a little easier.
    Thanks for the advice, I appreciate what you are saying as regards the loads.

    Sach

Similar Threads

  1. Rear axle hub!
    By Allora#2 in forum For Sale
    Replies: 0
    Last Post: 12-02-2019, 19:49
  2. Fiat Stub Axle Safety Washers
    By Guy Mayers in forum Stratos Forum
    Replies: 9
    Last Post: 01-04-2018, 23:52
  3. What front end is this?
    By maxxfish in forum Stratos Forum
    Replies: 37
    Last Post: 08-12-2017, 14:26
  4. Front Hub play
    By AndyH in forum Stratos Forum
    Replies: 11
    Last Post: 10-06-2014, 00:13
  5. Front bulkhead
    By Madham in forum Litton Corse, CAE, & Napiersport
    Replies: 9
    Last Post: 27-03-2012, 21:19

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •