Results 1 to 8 of 8

Thread: Panel Location Brackets

  1. #1
    Site Supporter ProtoTipo's Avatar
    Join Date
    Sep 2011
    Location
    Outer Mongolia
    Posts
    4,758
    Rep Power
    60

    Panel Location Brackets

    Wanted:

    Any of these: (see photos attached)
    Not the twin X1/9 rear panel release levers, I've got those.
    Attached Thumbnails Attached Thumbnails Graham Bates Location.jpg   Round Arch locator 1.jpg.jpg   GBrearcatch1.jpg.jpg   GBrearcatch3.jpg.jpg   GBrearcatch4.jpg.jpg  

    catchkit2.jpg   a3_1_b.jpg  

  2. #2
    Site Supporter ProtoTipo's Avatar
    Join Date
    Sep 2011
    Location
    Outer Mongolia
    Posts
    4,758
    Rep Power
    60

    Re: Panel Location Brackets

    More photos:

    Maybe Gerry has them, or GB. Failing that, I'll have to make some.
    Attached Thumbnails Attached Thumbnails Front Locating Bracket.jpg   Front Locating Bracket 2.jpg   Front Locating Cup.png   Graham Bates Locating 2.jpg  

  3. #3
    SEC Member Guy Mayers's Avatar
    Join Date
    Sep 2011
    Location
    Liverpool
    Posts
    3,309
    Rep Power
    46

    Re: Panel Location Brackets

    There was a set of these panel location parts with the kit I sold to Matt Oakley Chris - I don't know if he installed them though? Might be worth a PM? The set didn't include the big circular receivers for the rear bodywork/tub though, I think that's a part that's specific to the round arch Group 4 style though?

    I don't know if Gerry stocks the parts for the panel latches and centre pivot lever, worth an email? He might be prompted to get a batch made?
    Guy
    Last edited by Guy Mayers; 31-03-2024 at 11:27.

  4. #4
    Site Supporter ProtoTipo's Avatar
    Join Date
    Sep 2011
    Location
    Outer Mongolia
    Posts
    4,758
    Rep Power
    60

    Re: Panel Location Brackets

    Quote Originally Posted by Guy Mayers View Post
    There was a set of these panel location parts with the kit I sold to Matt Oakley Chris - I don't know if he installed them though? Might be worth a PM? The set didn't include the big circular receivers for the rear bodywork/tub though, I think that's a part that's specific to the round arch Group 4 style though?

    I don't know if Gerry stocks the parts for the panel latches and centre pivot lever, worth an email? He might be prompted to get a batch made?
    Guy
    Thanks Guy,
    At least I could find out the dimensions from Matt?
    It's the round arch type that I'm after, as on my ex Terry Bunn car. The front type are on all four corners of a Stradale.
    On OE Stradales there's a little plinth on the back for the rear locating cup. I don't need that though.
    I have sent Gerry an email.
    Attached Thumbnails Attached Thumbnails Rear Locating Cup.png  

  5. #5
    Site Supporter ProtoTipo's Avatar
    Join Date
    Sep 2011
    Location
    Outer Mongolia
    Posts
    4,758
    Rep Power
    60

    Re: Panel Location Brackets

    Quote Originally Posted by Guy Mayers View Post
    I don't know if Gerry stocks the parts for the panel latches and centre pivot lever, worth an email? He might be prompted to get a batch made?
    Guy
    Hawk bonnet pin towers too Guy:
    Attached Thumbnails Attached Thumbnails Hawk Bonnet Pin Tower.jpg  

  6. #6
    SEC Member Guy Mayers's Avatar
    Join Date
    Sep 2011
    Location
    Liverpool
    Posts
    3,309
    Rep Power
    46

    Re: Panel Location Brackets

    Don't recall seeing them on the shelves but the stocktake isn't for a few weeks yet!

    Guy

  7. #7
    SEC Member
    Join Date
    May 2022
    Location
    Northumberland
    Posts
    110
    Rep Power
    3

    Re: Panel Location Brackets

    I made a couple of bonnet pin towers just using some threaded bar and connecting nuts which seem to have worked well. On the rear on onside the alignment wasn't great so I got an alloy cone and fitted that on the inner wheel arch and cut a hole in the clam and fitted a steel washer around it and it acts as a locator and pulls the arch into place.

  8. #8
    Site Supporter ProtoTipo's Avatar
    Join Date
    Sep 2011
    Location
    Outer Mongolia
    Posts
    4,758
    Rep Power
    60

    Re: Panel Location Brackets

    Guy Matt,

    In the end, Ken Tomblin has sent me details of the bonnet pin brackets on his Hawk. I've copied these:
    I'm still going to use the alignment brackets, and obviously the over centre catches. 3 devices in total.
    Attached Thumbnails Attached Thumbnails Bonnet Pin GB.jpg  
    Last edited by ProtoTipo; 03-04-2024 at 11:40.

Similar Threads

  1. Alfa 166 caliper brackets
    By pim in forum Brakes
    Replies: 26
    Last Post: 24-02-2021, 14:19
  2. Exhaust silencers mounting brackets
    By Stratie.fr in forum Wanted
    Replies: 11
    Last Post: 08-01-2017, 09:12
  3. 164 Rear Caliper Brackets
    By Guy Mayers in forum Stratos Forum
    Replies: 0
    Last Post: 06-12-2014, 11:21
  4. Brackets for License Plate Molding
    By stratosfear in forum Stratos Forum
    Replies: 19
    Last Post: 26-11-2013, 21:35
  5. Alloy Radiators for Hawk - Fan Brackets
    By ducatiman in forum Hawk Cars
    Replies: 2
    Last Post: 21-04-2012, 21:24

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •